vasuptracker.blogg.se - Urc remote one for all

#Urc remote one for all manual
#Urc remote one for all code
#Urc remote one for all tv

Press the SET key to enter month setting mode.Īfter setting the month, press the SET key to enter the day setting mode.Īfter setting the day, press the SET key to enter the hour settingmode. If the SET key is pressed while in second display mode, the display will remain to display the second. Note: If the SET key is pressed while in the hour and minute or in the month and day display mode, the display will show the hour and minute for two seconds and then display the month and day for the next two seconds, then back and repeat again. Press the SET key to enter the clock setting mode. Setting up the clockįollow the steps below to set the current time and day. Note: At any of the above modes, pressing the SET key will enter theclock setting mode.

Press MODE key again, it will go back to display the hour and minute.

Press MODE key again within 2 seconds, it will display second on the right two digits.

The display will return to hour and minute if no key is pressed within 2 seconds.

Press the MODE key, the display will change to month and day.

The clock is preset to display the hour and minute. (model URC-5650 only) Changing clock display mode IMPORTANT: The Macro key will be the macro in ALL MODES.

When you hit the key you put the macro on it will automatically start thesequence.

PRESS "SETUP" and wait for two blinks - RELEASE.

PRESS the sequence of keys you want the remote to do.

PRESS the key (Macro 1 or 2) you want the Macro to be on.

Macro-Sequence Scrambled KeypadThis will allow you do do several functions with just the touch of ONEkey.

PRESS the button you want to clear twice.

PRESS the button you want to clear - RELEASE.

Now The volume is set for all original devices.

PRESS the VOLUME+ key, you will get two blinks.

Volume DefaultUse this to get the original volume to work on each device. NOTE: This only sets volume in the TV,VCR,CABLE, or SAT mode.

PRESS the device key you would like the volume to come from.

#Urc remote one for all tv

Punch ThroughThis sets Volume to work for one device in all modes.įor example, the TV volume will work in the cable and VCR modes. "SETUP" (2 blinks) 9 - 9 - 2, TV (you want to move TV)

PRESS the DEVICE key you want to replace.Įxample: If you want the Aux key to be a TV key:.

PRESS the DEVICE,(TV,VCR,CABLE,etc.),key you want moved.

If the remote DOES NOT blink it means the number is 0.

PRESS 4, carefully COUNT the number of blinks.

PRESS 3, carefully COUNT the number of blinks.

PRESS 2, carefully COUNT the number of blinks.

PRESS 1, carefully COUNT the number of blinks.

PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE.

#Urc remote one for all code

When your device turns OFF, PRESS the SETUP button and RELEASE it to lock in the code for your device.Make sure that the remote is pointed at your device during the search, You may have to press this sequences of buttons up to 100 times to search the entire library of codes. ALTERNATE slowly between the POWER key and the DEVICE(TV,VCR,CABLE,etc.) button until your device turns off.(On VCR,LD,and CD players use PLAY instead of POWER).ENTER 9-9-1 (two blinks on the remote).

Searching For Yor CodeIf you have tried all of the set-up codes for your brand of eqipment,or your brand is not listed, and you are still not able to get the unit torespond, try the following procedure to search for your code. PRESS the POWER button to test the code.You should receive 2 quick flashes after entering your code.ENTER the 4 digit code for your brand.PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.PRESS the button for the device you want to program,(TV,VCR,CABLE,etc.), then RELEASE.

#Urc remote one for all manual

Set UpAfter getting the proper codes from your manual or Customer Service,use the following instructions to enter them into your remote.